ARCADE MACHINE MAME HYPERSPIN HOW TO
ARCADE MACHINE MAME HYPERSPIN SOFTWARE
ARCADE MACHINE MAME HYPERSPIN PC
ARCADE MACHINE MAME HYPERSPIN WINDOWS 7
ARCADE MACHINE MAME HYPERSPIN TV

Make an account and download it here You will also needRocketLauncher you get from here Follow this tutorial with how to set it up.Дownload games from My Custom HyperSpin Intro is here. Cut the shapes (switches, buttons etc) in the back piece Wire up the arcade cables to the buttons using the diagram (this is for Minipac arcade only) The black daisy chain is the ground wire (Connecting power) this connect to all the Microswitches and back to the usb arcade board. Plug everything else in, secure harddrive, arcade control panelвЂ¦etc. This will be used for the marquee light as that came with no plug.Д¬onnect the On/Off Rocker Switch 240V in-between it.Дrill hole in Bottom piece for the led underlight.

ARCADE MACHINE MAME HYPERSPIN TV

Place in power supply use either small brackets or timber to keep in place.ДЄttach the 4 way lead extension to the back of the TV panel(screw or glue). Put your marquee artwork inbetween the 2x identical Marquee sheets and slot these in the top. Attach the TV using the bolts in the back of it. So in short every time you add a side you add a baton.(I wonвЂ™t keep repeating that part look at the pictures for where I added the batons/timber).Дrill the motherboard to the bottom piece making sure the ports are at the back. Remembering to screw the bottom piece 3-4 cm up the left/right pieces leaving a gap underneath to allow the under light to shine through. Then put the left & right pieces next to the bottom piece and drill together. 6cm wide) to each side of the bottom piece. Now that all the pieces are cut, screw a small chunk of the baton/ timber (approx. You may have to cut a couple of times to make it thick enough for the acrylic to sit in.(Approximately 2x2mm sheets of acrylic, so 4mm in total) Now use the circular saw on the top piece and Second to Top piece to cut 7mm deep, measuring 1.5cm in from 1 of the long edges. This indent will be for our T-moulding to sit in.

Using a circular saw cut a line down (dead centre) around side of the left & right pieces. Mini/Normal Circular Saw with Guide (needed for the T-Moulding & Marquee lines)Д¬ut 9 pieces of wood for the frame using 18mm MDFД¬ut-out 2 holes for the speakers to sit in the Second to Top Piece.

Wood Screws (I used Torx because you donвЂ™t have to drill pilot holes with these)Дў8mm spade or hole saw drill for arcade button holes Total (not including the PC) = Just under ВЈ250 Mini-PAC Arcade Cabinet Builders Kit ( FROM ВЈ76)Includes 2 concave buttons & 2 Bat style Joysticks There are cheaper versions for arcade kits but this comes with pre crimped wire, all colour coded and easy to use Winipac software. (Vinyl with sticky is expensive get posters printed on card and use Spray Mount)Д«lack Paint Tester (ВЈ3 I used the external paint)

ARCADE MACHINE MAME HYPERSPIN PC

PC power button (ВЈ15 This is optional.Looks Badass from .uk.Lighted Switch (Momentary)ДЎ0A Fused Snap In IEC Chassis Plug with Switch(ВЈ3Maplins/ Ebay)ДЄrtwork- ВЈ40? Will vary. On/Off Rocker Switch 240V (for Marquee light ebay/maplins ВЈ3)ДЈX Kettle leads aka IEC cables (ВЈ10 for PC power supply, monitor & main arcade system) Marquee Fluorescent Tube Light (Screwfix ВЈ12) (you could use USB LED light strip instead) USB LED light Strip (for under lighting ВЈ5 on ebay) Mini 2 Ch 12V, 2X 20W Hi-Fi Amplifier (Ebay ВЈ6) TFT Monitor 4:3 with VGA Cable (Refurbished ones are ВЈ25 on ebay)ДЎ8mmX28mmX180cm timber (Wickes ВЈ2 for securing the sides together like brackets)ДЈ4mm x34mm timber (Wickes ВЈ4 for securing the sides together like brackets)Дўmm Acrylic sheet (Wickes or Homebase ВЈ14)

ARCADE MACHINE MAME HYPERSPIN SOFTWARE

Hyperspin is a free bit of software that launches multiple console emulators all within 1 program. I found a few people online doing this using software called вЂњHyperspinвЂќ. What did I do with the Quad core PC?вЂ¦.Turned it into an EpiC arcade system JвЂ¦.

ARCADE MACHINE MAME HYPERSPIN WINDOWS 7

(Fast forward to present) It was time to buy a new PC and discard my old Quad core, 4GB RAM Windows 7 bundle of Joy for an I5. For just 1 game!!! I had played around with SNES & NES emulators on the PC for a while but using a mouse to launch these killed the authenticity of the arcade system so I forgot about it for a few years.

So when I finally bought my own house 3 years ago I looked into owning one of these bad boysвЂ¦. 2 Player Street Fighter II Bartop Arcade with HyperspinД«orn in the 80вЂ™s I was obsessed with button bashing arcade beatвЂ™ em ups like Streets of Rage, TMNT, Golden Axe etcвЂ¦And fighting games like Street fighter, Mortal Kombat, Tekken etc.

Arcade machine mame hyperspin